Read and participate in active technical discussions with automation and industrial controls users from all over the world.
Control.com - Nerds in Control
Member Login
Modbus Links
Search
Jump to a Date
Cool stuff
RSS Feed
Use this link to get an RSS feed of the Modbus Community article flow, for private, non-commercial use only:modbus.control.com/rss/
To get a personalized feed, become a member at no cost.
Can MODBUS TCP/IP devices share the same infrastructure with Ethernet/IP devices?
New Replies:
By Jerry Miille on 20 November, 2009 - 3:52 pm -
Sure, we do it all the time with our Omnii-Comm.
www.miille.com/266-P00-Ethernet.pdf
Jerry...
We are trying to built up communication of power meter pm-710 with egx-100.
New Replies:
By GENJUA on 20 November, 2009 - 3:10 am -
Mark, ya i try with end terminal resistor as well.
John Correa, know i am reading only 2...
By John Correa on 19 November, 2009 - 7:10 pm -
Only thing that can suggest (by now) is that you change the update rate of your MB_TCP driver. May...
By Mark on 19 November, 2009 - 5:03 pm -
Hello,
Jumping in the middle here and I might have missed something.
How about termination...
John Correa, sometimes i get the error which is NEGATIVE ACKNOWLDGE and sometimes the error is...
The EGX100 supports a total of 32 open TCP/IP connections at one time with the 2.7 firmware. It...
By John Correa on 18 November, 2009 - 4:28 pm -
Check the error message type in your EGX100. If the error message is TIMEOUT may be something wrong...
What is the difference between the first four mod bus commands?
New Replies:
By M Griffin on 16 November, 2009 - 8:41 pm -
Your division of:
DIN : Discrete Inputs
DOUT : Coils
AIN : Input Registers
AOUT : Holding...
Low cost power meter-data acquisition.
New Replies:
Raj,
I was not able to tell whether you need 3-phase or single-phase and whether this is for...
Problem transferring Binary data over the GPRS Network while communicating to a modbus rtu
New Replies:
Telnet is designed for 7-bit ASCII.
It doesn't allow raw 8-bit binary data - various bytes (such...
By M Griffin on 8 November, 2009 - 12:56 pm -
Modbus RTU can be sensitive to timing "gaps" in the message. It could be the GSM modem is...
Modbus Fire & Security Alarm System
New Replies:
> I need vendors for Fire Alarm and Security Alarm Panels that can communicate using...
I have some problems on the TCI.
it stops when the operating system of the HMI start.
it stops when the operating system of the HMI start.
Modbus TCPIP master to many slaves
New Replies:
By Ken E. on 30 October, 2009 - 7:51 am -
I would suggest to leave your 15 connections open for efficiency. It may not be necessary, but why...
Class not registered
Water/Gas Meter with Modbus/LonTalk/BACnet Compatibility
New Replies:
Hello Steve,
For your application, I recommend using a Sensus (or Sensus-compatible) water meter...
how a flow meter communicate
New Replies:
For your application, I recommend using a Sensus water meter and a Sensus gas meter, both of which...
By Steve on 17 October, 2009 - 7:46 pm -
Hi,
I am looking for a water meter and a gas meter that can output Modbus, LonTalk, or BACnet. Do...
Can MicroLogic PLC read Modbus Holding Registers in the 5xxxx range?
New Replies:
By M Griffin on 17 October, 2009 - 1:43 pm -
Thanks to Mark for the correction. It appears that old versions of the Modbus spec did make some...
By Mark on 17 October, 2009 - 2:25 am -
Hello,
What Mr. Griffin said is 99.99999% accurate.
The current specification: MODBUS...
The typical Modbus Address Scheme is :
0x = Digital Outputs (Bit)(Read / Write)
1x = Digital...
By Harvard on 15 October, 2009 - 11:31 am -
Try reading Register = 50102-40001 = 10101 = 0x2775...
By Patrick Lansdorf on 15 October, 2009 - 3:02 am -
Hi,
I cannot answer if a MicroLogic PLC can read 5xxxx registers. But if it cannot, I would...
none
need to link two modbus master devices
New Replies:
By Jerry Miille on 9 October, 2009 - 10:09 am -
You can use the MARC Omnii-Comm:
http://www.miille.com/din266-p00.pdf
for this type of...
INTERFACING SIEMENS S7 PLC WITH ABB AC800M + COMPACT HMI
New Replies:
By Rob on 8 October, 2009 - 11:02 pm -
Yes, you can if you wish. No, you don't require any other methods.
I assume your S7-313C PLC...
We need to talk to Crestron with a Beckhoff PLC, by using the Crestron read/write blocks
Grass root project looking a cheap way of bringing groups of temperature signals that are in close proximity into a DCS
New Replies:
By David on 28 September, 2009 - 7:10 pm -
HART is an FSK signal superimposed onto a 4-20mA signal from a field transmitter. The HART signal...
>> groups of temperature signals <<
> I would think that you mean thermocouple...
I tend to agree with David, I suspect that you are dealing only with temperature elements, please...
By David on 18 September, 2009 - 8:29 pm -
> groups of temperature signals <
I would think that you mean thermocouple direct because...
Clone to new OS with new hardware or Clone to new hardware with same OS?
I have no idea how to determine the Modbus RTU Framing times.
I am trying to integrate a Modbus RTU device (Emerson ROC809) into a HART communications network (digital HART FSK over 4-20mA loop) with a Siemens S7-400 with PDM.
New Replies:
By Dan W on 18 September, 2009 - 8:15 pm -
> I understand that PDM needs EDD files so that is not the issue. <
I suspect it is an...
Connecting KingFisher to Wonderware
New Replies:
Hi Herman,
I am using MBENET v 8.1 to communicate between TSX Premium PLC and Wonderware InTouch...
Your use of this site is subject to the terms and conditions set forth under Legal Notices and the Privacy Policy. Please read those terms and conditions carefully. Subject to the rights expressly reserved to others under Legal Notices, the content of this site and the compilation thereof is © 1999-2009 Nerds in Control, LLC. All rights reserved.