Read and participate in active technical discussions with automation and industrial controls users from all over the world.
Control.com - Nerds in Control
Member Login
Modbus Links
Search
Jump to a Date
Cool stuff
RSS Feed
Use this link to get an RSS feed of the Modbus Community article flow, for private, non-commercial use only:modbus.control.com/rss/
To get a personalized feed, become a member at no cost.
Borland C code for the Modbus RTU RS 232/485
Demux Status from MKV Modbus Map
Hi! Anyone use the HVAC controller-Carel (http://www.carel.com) to talk to any HMI over MODBUS protocol?
New Replies:
Hi.
Can u send me instruction to make a time schedule on a 2Q250 i/o module using Citect Desigo...
Hello,
I have the Carel IR32CEM100 controller which has the 485 interface adapter inserted into...
How to define item name in Wonderware Intouch
to read holding register in Janitza Power meter
to read holding register in Janitza Power meter
Has anyone ever successfully connected a GE Fanuc 90-30 to Labview 7-1?
Trouble establishing communications between a Quantuam 311 CPU programmed in Unity and Wonderware InTouch 9.5 and SA85 I/O Server ver 8.1
need a way to talk modbus from a custom VB HMI via land-line modem to 13 remote sites using Campbell Scientific data loggers
New Replies:
By William Sturm on 22 May, 2009 - 9:36 am -
I have used this drivers from these folks and they worked well for...
mA to modbus converter
New Replies:
By M Griffin on 14 May, 2009 - 9:30 am -
The Advantech Adam modules are low cost. The 4000 series does Modbus RTU over RS-485, and the 6000...
By DGH Technical Support on 14 May, 2009 - 7:05 am -
DGH offers current input modules with a Modbus RTU output. RS-232 and RS-485 versions are...
Please check: http://www.szsunyuan.com/sy/upload/ISOADA08.pdf
It provides up to 8 pairs of input...
By Roy Matson on 14 May, 2009 - 12:10 am -
Check out Moore Industries, I did something similar with their Data Concentrator modules.
...
Question about connection MVI56-Kepserver-WinCC
New Replies:
By Erik Syme on 12 May, 2009 - 8:13 pm -
The module would be setup as a Modbus Slave to the Kepware running the modbus master driver. The...
By alekos on 11 May, 2009 - 2:38 pm -
The problem is that from technical support from prosoft I received answer:
"You could...
By Fred Loveless on 11 May, 2009 - 9:59 am -
The MV156-MCM does modbus so you would use the Modbus Suite from Kepware to talk to it.
Fred...
abb scada communication error
Connect a Magelis XBTGT with Zelio Smart Relay via Modbus
New Replies:
Yes, but were I'm from, it cost me (din rail, distancer, rubber, labor included), cca 10Eur...
Yes thay can work with one XBTGT.
But for cost effective siutations (and not so elegant), you...
By John Caldwell on 11 March, 2009 - 3:35 pm -
You can display data or send control data to any number of Zelios from an XBT GT relay via ethernet...
Modbus master or slave
New Replies:
By aggattapauer on 20 April, 2009 - 2:02 pm -
Normally HMI is master on the bus, so you have to install the modbus slave into the CP341.
Why...
Choosing a control system for small gasifier
New Replies:
By Rob on 20 March, 2009 - 4:48 pm -
There's absolutely no point in re-inventing the wheel here. Microcontrollers & Modbus I/O is...
Does the MKV HMI act as a slave to the DCS?
New Replies:
Yes the MkV is a slave to the DCS via Modbus serial connection.
I know that both Global...
Question about a MODBUS slave for WINCE (XScale)
New Replies:
By M Griffin on 19 March, 2009 - 5:01 pm -
I would suggest looking for some C source code libraries. MS WinCE is a fairly obscure platform...
RTU over Ethernet Problem
New Replies:
By Fred Loveless on 18 March, 2009 - 1:32 pm -
Forgot to mention that his is what our Modbus RTU Serial driver does when you enable Ethernet...
By Craig on 17 March, 2009 - 3:55 pm -
Basically what I have is a touch panel (HMI) that has a Modbus RTU driver in it. If I run this...
That won't work, Craig. If you want to encapsulate Modbus RTU serial in a TCP or UDP packet you...
By Fred Loveless on 10 March, 2009 - 5:28 pm -
Yes as long as it is not adding a Modbus Ethernet header and footer to the packet. You want a raw...
By Craig on 10 March, 2009 - 2:38 pm -
So your saying if I use a serial RTU driver and go through a RTU to TCP convertor I should be good?...
By Fred Loveless on 3 March, 2009 - 1:59 pm -
Modbus over Ethernet is usually Modbus RTU encapsulation in an Ethernet Packet. Modbus TCP is...
Is there a windows-based diagnostics program that displays the status of a Schneider-Electric Quantum CPU over Modbus Plus?
Question about how to develop a software which is communicating on modbus/TCP
New Replies:
By M Griffin on 11 March, 2009 - 2:31 pm -
The Jamod web site has some very good explanations and examples. If there is something in...
Looking for Modbus addressing reference for Schneider-Electric power meter PM800.
Seeking an equivalent of a Siemense Simocode Pro V but with a Modbus TCP or straight ethernet output.
New Replies:
Andrew's request was for "a similar product to the Simocode that outputs direct MB/TCP",...
By YL on 9 March, 2009 - 8:25 am -
See the ABB's AC500 PLC.
Its small, extremely smart and fits for your needs. By default MB TCP and...
Configuration Modbus Slave TCP/IP on Citect Scada ver.7.0
Your use of this site is subject to the terms and conditions set forth under Legal Notices and the Privacy Policy. Please read those terms and conditions carefully. Subject to the rights expressly reserved to others under Legal Notices, the content of this site and the compilation thereof is © 1999-2009 Nerds in Control, LLC. All rights reserved.